The BST Thread (Buy, Sell, Trade)

[d42kn355]

oh thanks gods… i need more of both lolol
PM incoming

[devicex]

were do we find them listed ?

[KardashevTypeII]

I’ll be watching with significant interest.

-Fumu / Esopus

[popflier]

@devicex I don’t have them listed online right now. I will have the switches on Reverb and Tindie soon and the pots I’ll add later but I have been selling everything for slightly more on those sites than what I am offering them to the LMNC community for. (Pots are $9 for 10 for LMNC peeps and $11 for 10 on Reverb and Tindie.) If you’re interested you will just have to message me on here for the discount when I get the new stock back in. Switches are 2 for $1 and I do have plenty of those available right now.

[analogoutput]

Now up on Tindie:

• Noise Bells Kosmo PCB/panel sold out
• Euro/Kosmo protoboard
• Barton Sallen-Key Kosmo panel
• Attenuators Kosmo panel

Very limited quantities!

[d42kn355]

sweet.
I grabbed a Noise Bells and Barton Sallen Key

[Riggidyboo]

Ordered a Noise Bells.

[Enoharduino]

Wow I just found out that you sell your pcb and panel and they are really cheap!

[analogoutput]

Still available, 1 each of:

• Mikrokosmos (black panel) sold out
• Dual Quantizer (red panel)

[ChristianBloch]

Just snagged the last Noise Bells

[Farabide]

Just a heads up that in January I’ll be selling off a lot of my old studio and session gear. Mostly guitars and basses and odd bits of kit. I have gathered over 50 instruments in my near 40 years of performance but as im now going to be stuck in bed for the foreseeable future I’m thinking a pimped up electric chair might be of more use. Not sure how much to offer here and still trying to think about the logistics of photographing, listing and shipping (anyone with advice sing out).
In the meantime if you have a need just think "I wonder if Sandy has a … whatever " and message me. I’ll still be building, recording and playing when I can but given the size of my modular to do list I need the space. Best to all. X

[d42kn355]

my my… i would love a list… lol

[Farabide]

Just making a list will be a massive task in itself. A lot of my gear has been modded by me so it’s not enough to say “a pevey p60 guitar” when the phase switch is modified and the interior has been shielded. If I get the list done I’ll post it and if anyone has any links to synth mods for wheelchairs you know where to post them.

[Vumnoo]

@Farabide

if anyone has any links to synth mods for wheelchairs you know where to post them.

Wouldn’t two synth bikes side by side strapped together with gaffa tape basically do the job?

[Farabide]

Yay! But who’s pedalling? Plus as much as I’d love Dr Who I don’t want to end up looking like Davros!

[Farabide]

[Bitnik]

@Farabide

I don’t want to end up looking like Davros!

A dalek’s nightmare: a wisecracking Scotsman in Davros’s chair.

[CTorp]

Extra PCB sets up for grabs

$10each on the 5cm modules (have about 8 of each)
15 on the taxidermist (have a few left)

$6 shipping for USA.

Kosmo Sequential Switch

[image] [image] This is one of the modules I’ve been working on, the Kosmo sequential switch based on the fonitronik design. (fonitronik modular synth diy) It is a nice multipurpose utility module for cv or audio routing, apparently any signal up to 12v. It has one input that switches between up to 4 outputs and is reversible (4 in, 1 out), with manual push button and cv controlled reset and “clock.” As well as a switch to select how many switch steps you want to cycle through (2-3-4). For e…

Kosmo format multiples

[image] [image] [image] Pcb sets for two types of multiples both in 5cm kosmo, a doepfer style switched-mult and a buffered/passive mult combo. There isn’t a whole lot to say about them, the buffered mult is one of the better ones I’ve seen in opinion, with trim pots on each output so you can match them exactly. Here is the original schematic: [image] I changed his fancy pants resistors and the trim pots and still have the outputs tuned to within .01v of each other. I doubled the design fo…

Kosmic Taxidermist

Finally getting back into some kicad noodling, working on modding and porting the “Phonic Taxidermist 47.2b” from circuitbendersUK to a kosmo faceplate: it is basically a delay as well as a strange “distortion” circuit (they call it a chopper). it sounds like it has a ring mod to bit crush range of effect. it works by strobing the audio signal at different frequency bands which can be selected with the four switches. a guy on muffwiggler by the name of MCOP has also added gate control to the…

[popflier]

I have received more stock of B10k and B100k 6.35 round shaft pots. These do not have the tabs on them. If anyone is interested in purchasing some the cost for LMNC people is $9 for 10 + shipping. Shipping is usually $4 - $5.50 depending on where you live in the US and the quantity you purchase. Includes all washers and nuts needed.

I also have switches if anyone needs those. They are 2 for $1. I have:

SPDT - on-off-on
DPDT - on-on
DPDT - on-off-on

[Caustic]

Lookin to sell my Keystep Pro. I like it, but my needs have shifted and I need the space. Was going to make a listing on reverb, but I thought I could mention it here first. I have the box, and the original USB cable along with it. Looking to ship only to the contiguous US for shipping cost reasons. Open to offers, just DM me for details.

It will be around mid December before I will be able to ship.

Original Keystep is now sold.

Also have an original Keystep that does not have its box, but does have the original USB cable that i am looking to sell.

I want to add that I’m open to throwing in some front panels I made a while back, since it wouldn’t add much to the shipping.

Im going to leave this up for a bit, so there isnt a huge rush for everyone.

Freebie:
The Caustic VCF / VCO front panel greens i had made a while back. The holes are just a hair narrow, so you would have to widen them a bit. Someone wanted me to sell them, but with this error, i can only in good conscience give them away. They mount the tayda stripboards, so this is perfect for the stripboard version of the VCO / VCF. To be clear, these are just the front panels.